FERROLI WFL4+P7 PELLET ΤΑΞΙΑΡΩΝ. By – Ποιότητα & Οικονομία · Updated about 5 years ago · Taken in περιστερι · Already tagged. Gorilec na pelete Ferroli z visokim učinkom in omejenimi emisijami za kotle na trda goriva razreda 3 EN , zanesljiv, enostaven za uporabo in vzdrževanje.
|Published (Last):||27 June 2010|
|PDF File Size:||2.60 Mb|
|ePub File Size:||12.8 Mb|
|Price:||Free* [*Free Regsitration Required]|
And, even stranger, at the slightest movement the pellets that were jammed on the tube would start to fall down in the grille, sometimes while I was opening the door. So the pipe connecting the pellets to the burner would overheat, and upon doing so the dust from the pellets we believe, would become sticky as the pellets were being fed into the boiler, this would in turn block the gasket pipe.
Hi, thanks for the information.
Stuck SUN P7 pellet burner – how to fix. – Jurnal
They got stuck a couple of times a week!! I just want to clarify something please. Does any one knows how to solve this issue. Still smoke, but flame fegroli nice and full……….
Nino wants to know if this verroli to you? So we have now also fixed that little problem, as I had said before our chimney was too short and we purchased from the UK a Vedetta cowl, http: Thank you …sorry for my bad english….
For the smoke problem see answer given to Safari. Hi Safari, nice to see you found the problem. I tried to derroli very well the tube and the metallic neck but to no avail.
I also disconnected the boiler sensor and set this in parameter t02 to 0 without success. I had this problem. Have any one have advice how to reduce pellet consumption. Because when its cooldown. Before playing with that I would like to ask if anyone knows, what decides when are power levels changed?
I will be happy if you can answer me quickly. See the table in the article. The burner tube was destroyed at the very end top side. Can you tell me how to increase the spacing between gear changes in modulation? The price is exactly half of cheapest one bulgarian that I can find here.
OK, we now understand that the conversion that we had done was not appropriate for our old oil burner, and the overheating came from the fact that the old boiler could not cope with the heat output. When I would open the burner door, or at the slightest move, the bridge would colapse and pellets would fall down in the gril. It helped me big time! As for unburned pellet, I think that the problem is with smaller pellets, they are too light and fan just blows them away.
FERROLI WFL4+P7 PELLET ΤΑΞΙΑΡΩΝ
From my knowledge it is supposed to be around celcius measured 20cm from the exaust output of your boiler. The burner SUN P7 from Ferroli has a minimum of automation, which means that is has no extra sensors apart from was is strictly necessary to function and for safety. I never use the burner like this. At the slightest movement the pellets would fall in the grille. The manufactor sent me a new one and now it is quiet. Good morning, we are using SUN 12 I just want to clarify something please.
We had a habit, everytime we entered that room we leveled the pellets actually build a small hill of pellets on top of the auger. To quit the menu, hold P until the clock appears again 10 seconds.
The actual load time is always around 4 seconds but the pause, wait period until next load changes. If anyone knows how and what to press i will be greatfull. Hello I think its not only put to hot. Carissimo Antonis, voglio comunicarti che ieri, con temperatura esterna 3 gradi, il mio bruciatore inserito in una vecchia caldaia delha raggiunto e funzionato perfettamente.
To clean it, you also have to take the red cover off. Also you need to clean your chimney periodically.
In the first part of the cycle it will not load pellets, fefroli the second it will load pellets. After a few minutes he started again and do exactly the same. I always buy premium pellets.
For each setting you can set any power level, from minimum to maximum. But I am in a trouble now. Nice explanation of operation, thanks!!!
That is a protection temperature sensor. Saluti p grazie per le eventuali risposte. This could be a good lead Thanks! Do you use the burner just for hot water and no heating?